search

A&D Weighing Indicator AD-4407 Spécifications Page 42

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 66
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 41
Page 40 AD-4407 Weighing Indicator
f22
f22f22
f22 =
= =
= 9
99
9 (Check weighing 3:Loss in weight)
(Check weighing 3:Loss in weight) (Check weighing 3:Loss in weight)
(Check weighing 3:Loss in weight)
Output and Condition
Output and ConditionOutput and Condition
Output and Condition
* Relay OK output can be changed to the OVER or UNDER by f24.
Triangle 2 is displayed when Gross Full regardless of the f24.
OVER/UNDER is judged always and the result is output to the LED and the relay.
10.2.2. Simple Batch
The weighing sequences of Simple batch (f22 10, 11 or 12) are similar to those of
Check weighing (f22 7, 8 or 9) respectively. The differences are listed below.
1 Basically ON/OFF of the relay and the LED is reversed.
2 No judgement other than Zero band and Full before input Start signal.
3 The weighing completion condition is set by f23 2x and it is effective after Start.
4 The outputs of Preliminary and Free fall are off from weighing completion to the
next start.
5 Weighing completion can be output by f24 and f25.
6 The start signal can be accepted after weighing completion even the weight is not
within the zero band.
7 Over/Under output is set by f23 3x.
Start
StartStart
Start
Tare when the Start is input automatically if f23 11.
The READY mark turns off when the Start is input.
Weighing Completion
Weighing CompletionWeighing Completion
Weighing Completion
The weighing completion condition is set by f23 2x
f23 20 : Either the STOP key is pressed or the Batch stop input is on
f23 21 : Stable is detected after reaching Final
Before reaching Final, the STOP key or Batch stop input forces weighing
completion even if f23 21 .
10.2. Setpoint Comparison
Final
Wei
g
hin
g
value
Calibrated Zero
Tare
Tared Zero
Zero band
Free fall
Preset target weight
Time
Weighing
Rela
y
HI, 1, -Net -
(
Final - Free fall
)
Rela
y
OK*, 2, Gross Full
Rela
y
LO, 3, Gross Zero band
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
Vue de la page 41
1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 65 66

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Mesure, test et contrôle A&D Weighing Indicator AD-4407
Mesure, test et contrôle A&D UT-101 Manuel d'instructions   (24 pages)
Mesure, test et contrôle A&D Density Determination Kit AD-1653 BM Series Manuel d'utilisateur   (4 pages)
Mesure, test et contrôle A&D TM-2564G Manuel d'instructions   (62 pages)
Mesure, test et contrôle A&D OP-03 Manuel d'utilisateur   (10 pages)
Mesure, test et contrôle A&D Series 57ZZ Manuel d'utilisateur   (44 pages)
Mesure, test et contrôle A&D Multi Function Weighing Indicator AD-4402 Spécifications   (146 pages)
Mesure, test et contrôle A&D OP-05 Manuel d'utilisateur    (4 pages)
Mesure, test et contrôle A&D GR Series Manuel d'utilisateur   (3 pages)
Mesure, test et contrôle A&D Digital Comparator AD-8512 Manuel d'utilisateur   (4 pages)
  • Security Point Tommy Docks Acomdatacom VIRTUAL Mark white air conditioning
  • Kenwood Composants de châssis Altec Lansing Haut-parleurs Compaq Ordinateurs portables de poche Kicker Radios Polaroid Flashs d'appareils photo
  • BOEN SN-20015 Yamaha YDP-162 Aiwa XR-EM70 Whirlpool WSFC 3M17 X
  • Flowserve G4 Durco Manuel de l'utilisateur Black & Decker Dustbuster Flexi PD1200 Manuel d'instructions LG GX500 Manuel de l'utilisateur Kichler 42909 Manuel de l'utilisateur Acer TravelMate P256-MG Manuel de l'utilisateur